Aeon labs z-stick series 2 factory reset

One turn without the other, therefore, will reset the Nano-Dimmer. With other switches this might not be too bad but, with my lampsвЂ™ modified 3-way switches, вЂњholdingвЂќ a switch is one turn while вЂњreleasingвЂќ it is one more. That is, when its momentary switch is held for 20 seconds, it resets. Unfortunately, after completing this integration, I stumbled over a Nano-Dimmer вЂњfeatureвЂќ. Remote control may be done indirectly with smarts (SmartThings) or by direct association with a Z-Wave dimmer/switch. This was connected to S1 on the Nano-Dimmer. I harvested a terminal from yet another socket and replaced this one so as to have a wire binding screw on it. To insulate these from each other, I added a sleeve of shrink tubing to the bottom one and folded it over to separate it from the top one.ДЇor my socket, the other switch pole of interest was conveniently connected to another terminal. This is connected to OUT on the Nano-Dimmer. I was able to bend the tail on the central socket contact under the screw on the top terminal. This is connected to COM on the Nano-Dimmer. The bottom remained connected to the switch common. To this end, I harvested a terminal from another socket, split them in half (actually, ~ 2/3-1/3) and fit them both back in the same slot with the top one flipped. Now this central socket contact must be wired directly to OUT on the Nano-Dimmer. It was designed to switch this to the other poles - one of which is wired to the central socket contact and, from there, to the bulb. The switchвЂ™s common pole was intended for the live supply.

The live supply wire is connected only to L on the Nano-Dimmer. The neutral supply wire is connected to the socketвЂ™s neutral binding post and to N on the Nano-Dimmer.

Rivets can be replaced later with small machine screws. Remove rivets, socket and insulating cap to access switch internals. Dimmable bulbs are used instead of 3-way ones.ДЈ-way lamp socket surgery was delicate and should only be attempted with great care.Дrill out rivet heads from inside socket. Pausing after the first turn causes the Nano-Dimmer to dim up and down, alternately. From the open position (I marked with a horizontal line of paint across the knob), the light can be toggled (on/off) with two turns - emulating a momentary button press. It is the common and this pole that should be used to control the Nano-Dimmer in a вЂњmomentary switchвЂќ configuration. Note that one of the poles alternates between open and closed with each quarter turn of the switch. It seems to me that this basic needвЂ“to not stumble around in the darkвЂ“is a great application for smart switches and bulbs, but IвЂ™m getting nowhere at making it happen. I recently saw a very elaborate вЂњSmart HomeвЂќ setup at a trade show and asked the demo guy this question and he looked at me as though I was asking him to solve differential equations. The MOST ideal would be a Z-wave enabled lamp socket with local control, but I havenвЂ™t found anything like that.

If I removed the bedside table switches, and rewired the outlets to always-on, and installed smart bulbs and a smart wall switch, then guests could have wall control, but how would they have local control? There is no hope of guests using an appвЂ“it has to be super-easy, ideally just a button on the bedside lamp that would turn the lamps off individually, but they would come right on when the wall switch was next toggled. IвЂ™m wondering if there is any way to smartify this system. So I turn on both bedside lamps, then turn the wall switch off so guests can walk in, turn on the light, and not stumble around in the dark. ItвЂ™s obvious that guests turn off the lamps by the switch on the lamp, so next day the wall switch does nothing. The wall switch does not control any ceiling lights, but switches the power to the outlets on either side of the bed into which the bedside lamps are plugged. I have a guest cabin with a master bedroom and some very nice bedside lights.

Aeon labs z-stick series 2 factory reset